〖USA〗4Axis USB Mach3 CNC Kit Nema 23 Stepper Motor 270oz.in 3A+ 4P TB6600 Driver

Description

【USA Stock & Located in USA & fast shipping】
Ship from
USA
Warehouse
by UPS/USPS
free VAT
&
free import duty
fast shipping service ship to US Customer
〖USA〗4Axis USB Mach3 CNC Kit Nema 23 Stepper Motor 270oz.in 3A+ 4P TB6600 Driver
for CNC Router Milling Engraving Machine
Parcel include:
4× 23HS8430 Nema23 stepper motor 76mm 270oz-in 3A
4× TB6600 stepper motor driver
1× 4 Axis USB Mach3 control board
1× USB Cable
1× 350W 24V DC switching power supply
1× CD disc include software & user manual
Nema23 Stepper motor
Main specifications:
* Motor Type: Hybrid Stepper
* Step Angle: 1.8 deg.
* Holding Torque: 1.8Nm (270oz.in) 18kg.cm
* Phase Resistance: 1ohms
* Rated Current/phase: 3A
* Inductance:3.5mH+/-20%(1KHz)
* Frame Size: 57x57x76 mm
* Number of Leads: 4
* Weight: 1.1kg
* Shaft:8mm diameter single shaft
Other Specification:
Step angle accuracy: ±5%(full step,not load)
Resistance accuracy: ±10%
Inductance accuracy: ±20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ----------—20deg ~+50deg
Insulation resistance:100MΩ Min,500VDC
Insultion Strength--------500VAC for one minute
Wiring
Stepper motor's red wire connect to driver's A+ port
Stepper motor's green wire connect to driver's A- port
Stepper motor's yellow wire connect to driver's B+ port
Stepper motor's blue wire connect to driver's B- port
TB6600 Stepper Motor Driver
Advantages:
working voltage is DC 10V-45V.
The output current is steplessly adjustable.
Automatic half-flow function
Adopt enlarged radiator, good heat dissipation
With output short-circuit protection function.
More informations:
The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.
The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.
The motor rotates forward when CW is high or suspended, and reverses when it is low.
When EN is onhigh or floating, it is working state, when it is on low, it is offline.
Note:
The power supply cannot be connected reversely, otherwise the chip will be burnt out.
The set current should not exceed the rated current of the motor.
Features:
The subdivision setting instructions are printed on the back of the board.
It adopts the common anode input mode, there are two input terminals, the wiring is more convenient;
Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
Parameters:
The working voltage is DC 10V-45V. recommended DC24V;
Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
The rated maximum output reaches: ±4.5A.
Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors which currently within 4.2A.
Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.
Read less
Terminal & Subdivision settings:
Wiring diagrams
4 Axis USB Mach3 Motion Control Board
1. Support for 4-axis linkage, you can connect four stepper motor drives or servo drives;
2. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;
3. 4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop
switch, auto tool zero, home switch etc.
4. Support for connecting electronic handwheel;
5. Have 0-10V signal output , you can use mach3 software to control the spindle motor speed.
6. 4 general-purpose isolated relay drive output interface, can drive four relays for controlling
the spindle starts, forward rotating and reverse rotating, pumps or other device;
7. 1 status LED, indicate connection status on the board.
Please strictly follow the instructions and warnings before using this product:
It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.
This USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify.
Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.
the output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.
350W 24V DC switching power supply
DC output: 24V 0-14.5A
DC voltage of Adjustable range: ±10%
AC input voltage range: 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by switch
Overload protection: 105%-135% cut off the output, automatic recovery
Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover
Working Temperature: -10℃～+50℃
Functions:
Shipping
Please open the package and check if there are some damages before sign,if there are some damages,please do not sign and contact us immediately.
Payment
Only accept paypal payment method.
Payment must be made within 3 days.
Problem&Feedback
Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it.
Pls contact us before you want to leave any negative feedback.
Refund
Any reason required for all refund. Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.
When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos.